pvc塑胶地板焊枪大功率塑料焊枪ppr工具pe板热熔机pp焊接枪
PVC plastic floor welding gun, high-power plastic welding gun, PPR tool, PE board hot melt machine, PP welding gun
进口品质大功率塑料焊枪
Imported high-quality high-power plastic welding gun
24小时连续工作 大功率 9档温度调节
24-hour continuous operation high-power 9-speed temperature adjustment
纯铜线电机
PURE COPPERWIRE MOTOR
噪音小|更省电|更耐用
Low noise | More energy-efficient | More durable
应用范围
APPLIED RANGE
广泛应用于防水膜、防水卷材、防渗衬垫、广告布、篷布、塑料管道、汽车保险杠、运动地板、珍珠棉加工、电镀槽、电子元件、PP\PE\PVC等板材和膜结构的焊接、土工模的局部焊接及修补。
Widely used in the welding of waterproofing membranes, waterproofing membranes, anti-seepage liners, advertising fabrics, tarpaulins, plastic pipes, car bumpers, sports floors, pearl cotton processing, electroplating tanks, electronic components, PP/PE/PVC and other sheet and membrane structures, as well as local welding and repair of geotextiles.
发热丝
IPORTED EATING WIRE
升温快【热稳定性好【发热均匀
Fast heating, good thermal stability, and even heating
9档调节
NINE GEARTEMPERATURE CONTROL
30-650度|准确控温
30-650 degrees | Accurate temperature control
过热保护调温器
OVERHEAT PROTECTION
超过设定值时，自动断开电路使电器得到保护
When the set value is exceeded, the circuit is automatically disconnected to protect the electrical appliances
防震动平衡叶轮
BALANCE IMPELLER
低振动|少噪音
Low vibration | low noise
使用及注意事项
1、初次使用时，可能会出现喷火或冒烟。此属正常现象，通电5分钟后会自动消失.
2、作业时，先将温度旋钮调到最低档位，通电后根据焊接需要，再逐步提高，达到焊接所需的温度。
3、停机前先将旋钮指向“0”处，吹风数分钟，待枪筒冷却后方可关机，以免余热损坏机件。4、操作时手勿触及枪筒，以免烫伤焊枪用毕要轻放，以免摔坏枪芯部分耐火瓷料，而使电热丝短路5、塑料板材被加热到130-140度时即成为柔软状态，稍加压力即可成型。焊接温度一般为240度左右，离焊接喷嘴口约5-10MM处的温度为200-260度;焊接时应注意喷嘴与焊点间的距离。以获得理想的焊接温度。6、电热丝断后，可旋开枪壳连接螺丝，取出枪芯，用相同规格的枪芯换上即可。
Usage and precautions
- When using it for the first time, it may produce sparks or smoke. This is normal, and it will automatically disappear after 5 minutes of powering on.
- When operating, start by adjusting the temperature knob to the lowest setting, then gradually increase it according to the welding requirements to reach the necessary temperature for welding.
- Before shutting down, turn the knob to “0”, blow air for a few minutes, and wait for the gun barrel to cool down before turning off the machine to prevent damage from residual heat.
- Do not touch the gun barrel during operation to avoid burns. After using the welding gun, handle it gently to prevent damaging the fire-resistant ceramic parts and causing a short circuit in the heating wire.
- When the plastic sheet is heated to 130-140 degrees, it becomes soft and can be molded with slight pressure. The welding temperature is generally around 240 degrees, and the temperature 5-10mm away from the welding nozzle is 200-260 degrees. Pay attention to the distance between the nozzle and the welding point to achieve the ideal welding temperature.
- If the heating wire breaks, unscrew the gun shell connection screw, remove the gun core, and replace it with a core of the same specifications.
Reviews
There are no reviews yet.